Skip to content
EN
  • Español
  • English
Advertisement

Rolling offset calculator for pipe fitters

Work out the travel between two fittings to offset a pipe up and sideways at once, the true offset, the run, the roll and the cut length after fitting take-off.

Fill in 3 of the 4 fields and the missing one is calculated. You can type in any of them.

°
The distance from the end of the fitting to where the centre lines cross. For a long-radius 45° elbow, about 0.41 times the radius; enter 0 if you measure centre to centre.
True offset—
Run (advance along the pipe)—
Roll of the fitting from vertical—
Cut length of pipe—
Fitting constant (1 / sin θ)—

Use this calculator for reference only, as we cannot guarantee that the results are free of errors.

Disclaimer

https://dyaii.es/en/rolling-offset-calculator/

Advertisement

When a pipe has to get round something by rising and moving sideways at the same time, the fitter does not use four elbows: two identical fittings, rolled, with an inclined piece between them make both offsets at once. This is the rolling offset. The calculator gives the length of that piece, how far the pipe advances while offsetting, how far to roll the fittings and the cut length; or, backwards, the offset reached with a given travel or the fitting angle needed.

Formulas

T = √(V² + H²)  ·  travel = T / sin θ  ·  run = T / tan θ
roll = arctan(H / V)  ·  cut = travel − 2 · c

V is the rise, H the roll, T the true offset (the diagonal of the rectangle they form), θ the fitting angle and c the take-off of each fitting, from its face to where the centre lines cross. Everything is measured centre to centre of the pipe.

Fitting constants

Fitting1 / sin θ (travel)1 / tan θ (run)
60°1.1550.577
45°1.4141.000
30°2.0001.732
22.5°2.6132.414
11.25°5.1265.027
Advertisement

Worked examples

  1. 300 mm rise and 400 mm roll with 45° fittings: T = 500 mm, travel = 707.1 mm, run = 500 mm, roll angle 53.1°.
  2. The same with 45° fittings taking off 60 mm each: cut = 707.1 − 120 = 587.1 mm.
  3. What roll does a 1 m travel give with 30° fittings and a 200 mm rise? H = √((1 · 0.5)² − 0.2²) = 458 mm.

Several ways to work it out

  • With the box: picture a box of height V, width H and length the run; the travel is its diagonal. This is what the drawing shows.
  • With the constant: true offset times the fitting constant (1.414 for 45°), no sines needed.
  • With a square: mark V and H at right angles on a board and measure the diagonal: that is the true offset T.
  • Simple offset (in one plane): if H is 0, the travel is V / sin θ; the most common case.

Any other triangle comes from the trigonometry calculator, the weight of the piece from pipe weight and its growth with heat from thermal expansion.

Advertisement

Frequently asked questions

How do you calculate a rolling offset?

First the true offset, T = √(rise² + roll²); then the travel, T / sin θ, and the run, T / tan θ. With a 300 mm rise, 400 mm roll and 45° fittings: T = 500 mm, travel = 707.1 mm and run = 500 mm.

What is the fitting constant?

1 / sin θ: what the offset is multiplied by to get the travel. For 45° fittings it is 1.414; 60°, 1.155; 30°, 2; 22.5°, 2.613.

How far do I roll the fitting?

arctan(roll / rise) from vertical: with a 300 rise and 400 roll, 53.1°. Both fittings are rolled the same so the travel lies in one plane.

How long do I cut the pipe?

The centre-to-centre travel less the take-off of each fitting, twice, plus the socket depth if the fittings are socket-weld or push-fit.

Related calculators

Share

WhatsApp X LinkedIn Telegram Email
Advertisement

Install Diseño y automatización de instalaciones industriales on your phone

All the calculators one tap away, full screen, like an app. It takes no space and is always up to date.