Skip to content
EN
  • Español
  • English
Advertisement

Timber beam calculator: maximum span and depth

Work out the maximum span of a timber beam, joist or lintel from its section, strength class (C24, GL24h…) and load, or the depth needed for a span.

Fill in 4 of the 5 fields and the missing one is calculated. You can type in any of them.

House floor: about 1 kN/m² of self-weight and finishes plus 2 imposed (3 in total). Light roof: 1 to 1.5 kN/m² plus snow.
L/300 for floors; L/400 with brittle partitions; L/200 for roofs.
Advanced options (3)

They come with a typical value: change it only if you know it.

Span allowed by bending—
Span allowed by shear—
Span allowed by deflection—
Design moment at that span—
Bending stress—
Deflection at that span—
Timber in the beam—

Use this calculator for reference only, as we cannot guarantee that the results are free of errors.

Disclaimer

https://dyaii.es/en/timber-beam-span-calculator/

Advertisement

A timber beam or joist supported at both ends has to carry its load without breaking (bending and shear) and without bending too much (deflection). The calculator gives the maximum span of a section under a load, or the depth, width or load it allows for a span. It is a preliminary design based on Eurocode 5: for a real project, have it signed off by an engineer.

The three checks

Bending: qd · L² / 8 ≤ fm,d · b · h² / 6
Shear: qd · L / 2 ≤ fv,d · kcr · b · h / 1.5
Deflection: 5 · q · L⁴ / (384 · E · I) ≤ L / 300

The load per metre is the load per m² times the beam spacing. The design load qd uses an average factor of 1.4 (1.35 for dead load and 1.5 for imposed load). Design strengths are fd = kmod · fk / γM, with kmod = 0.8 (medium-term load, indoors) and γM = 1.3; kcr = 0.67 allows for splits. Deflection uses the unfactored load and I = b · h³ / 12. The maximum span is the smallest of the three.

Strength classes

Classfm,k (MPa)fv,k (MPa)E0,mean (MPa)Timber
C16163.28,000Ordinary-grade pine
C18183.49,000Radiata and maritime pine
C24244.011,000Scots pine, spruce, the most common
C30304.012,000Selected timber
GL24h243.511,500Glued laminated timber
GL28h283.512,600Glued laminated timber
D30303.911,000Oak and other hardwoods
Advertisement

Several ways to get each value

  • The maximum span of a beam you already have: enter its section and the load.
  • The depth needed for a span: enter the span and clear the depth.
  • The spacing between joists for a section and a span: clear the spacing.
  • The load allowed on an existing floor: with the span and the section, clear the load.
  • Rule of thumb: for C24 house floors, depth is about L/20 to L/22 (200 mm for 4 to 4.5 m).

Tips

  • Deflection almost always governs: if it is not enough, increase the depth rather than the width (stiffness grows with h³).
  • Over time timber creeps and deflection grows (kdef = 0.6 indoors): so do not use up the whole deflection limit.
  • Supports need at least 80 to 100 mm of bearing and protection from damp.
  • For steel beams or other supports and loads, use the beam calculator.
Advertisement

Frequently asked questions

What span can a 75 × 200 mm timber beam cover?

In C24, at 500 mm centres and with 3 kN/m² (house floor), about 4.5 m: deflection L/300 governs (bending alone would allow 5.3 m). At 400 mm centres, almost 4.9 m.

How is a timber beam designed?

Check bending (M = q·L²/8 against fm,d · b·h²/6), shear (V = q·L/2 against fv,d · kcr · b·h / 1.5) and deflection (5·q·L⁴ / 384·E·I against L/300). The maximum span is the smallest of the three.

What is C24 timber?

A strength class from EN 338: 24 MPa characteristic bending strength and 11,000 MPa modulus of elasticity. It is the most common grade for structural pine and spruce. Glulam GL24h has similar values but is more uniform and comes in large depths.

Why does deflection usually govern?

Timber is strong but not very stiff (E of 8,000 to 14,000 MPa, 15 to 25 times less than steel). For spans over 3 or 4 m, the beam bends too much before it breaks.

Related calculators

Share

WhatsApp X LinkedIn Telegram Email
Advertisement

Install Diseño y automatización de instalaciones industriales on your phone

All the calculators one tap away, full screen, like an app. It takes no space and is always up to date.