Skip to content
EN
  • Español
  • English
Advertisement

Reynolds number calculator: laminar or turbulent flow

Calculate the Reynolds number of a fluid in a pipe and whether the flow is laminar, transitional or turbulent. Also the velocity, flow or diameter.

Fill in 2 of the 4 fields and the rest are calculated. You can type in any of them.

Kinematic viscosity—
Water density—
Water dynamic viscosity—

Use this calculator for reference only, as we cannot guarantee that the results are free of errors.

Disclaimer

https://dyaii.es/en/reynolds-number-calculator/

Advertisement

The Reynolds number tells you how a fluid moves inside a pipe: in orderly layers (laminar flow) or in eddies (turbulent flow). Head losses, heat transfer and the size of pumps and heat exchangers all depend on it. With this calculator you get it for water, air, diesel, hydraulic oils or any other fluid, and also the other way round: the velocity, flow rate or diameter that give a Reynolds number.

How to use the calculator

  1. Choose the fluid. For water, type its temperature: the density and viscosity are taken from tables. If your fluid is not listed, choose “Other” and type its density and dynamic viscosity, or just its kinematic viscosity.
  2. Of these four values, type two: inside diameter, velocity, flow rate or Reynolds number. The other two are calculated.
  3. In the drawing, drag the arrow on the flow regime bar: it sets that Reynolds number and the calculator gives you the velocity and flow rate that produce it. With the keyboard, focus the arrow and use ← and →.

Reynolds number formula

Re = ρ · v · D / μ = v · D / ν

Where ρ is the fluid density (kg/m³), v the mean velocity (m/s), D the pipe inside diameter (m), μ the dynamic viscosity (Pa·s) and ν the kinematic viscosity (m²/s), which is ν = μ / ρ. Re has no units: it compares the inertial forces of the fluid with the viscous forces.

If you know the flow rate instead of the velocity, the mean velocity is:

v = Q / A = 4 · Q / (π · D²)
Advertisement

Laminar, transitional or turbulent

Reynolds numberFlow regimeHow the fluid moves
Below 2300LaminarIn parallel layers, without mixing. The center moves twice as fast as the mean velocity.
From 2300 to 4000TransitionalUnstable: it switches from laminar to turbulent with any disturbance.
Above 4000TurbulentIn eddies that mix the fluid. The velocity is almost the same across the whole section.
These are the practical limits for circular pipes. In water systems the flow is almost always turbulent: at 1 m/s in a 50 mm pipe, Re ≈ 50,000.

Worked example

Water at 20 °C (ρ = 998.21 kg/m³, μ = 1.0016 mPa·s) at 0.1 m/s through a pipe with a 50 mm inside diameter:

ν = 0.001 001 6 / 998.21 ≈ 1.0034 · 10⁻⁶ m²/s
Re = 0.1 · 0.05 / 1.0034 · 10⁻⁶ ≈ 4983 → turbulent

The flow rate is Q = 0.1 · π · 0.05² / 4 ≈ 0.000 196 m³/s ≈ 0.707 m³/h. For the flow to stay laminar (Re = 2300), the velocity would have to drop to 2300 · 1.0034 · 10⁻⁶ / 0.05 ≈ 0.046 m/s.

Water viscosity vs. temperature

The viscosity of water drops a lot as it heats up, so at the same velocity the Reynolds number goes up. Values at atmospheric pressure:

Temperature (°C)Density (kg/m³)Dynamic viscosity (mPa·s)Kinematic viscosity (cSt)Velocity for Re = 2300 in 50 mm (m/s)
0999.841.79141.7920.082
10999.701.30591.3060.060
20998.211.00161.0030.046
30995.650.79720.8010.037
40992.220.65270.6580.030
50988.030.54650.5530.025
60983.200.46600.4740.022
80971.790.35400.3640.017
100958.350.28160.2940.014

Source: CRC Handbook of Chemistry and Physics and IAPWS. The calculator interpolates every 5 °C.

Other fluids in the list

FluidDensity (kg/m³)Kinematic viscosity (cSt)Re at 1 m/s in 50 mm
Air (20 °C, 1 atm)1.20415.063320
Diesel (40 °C)820316,667
Hydraulic oil ISO VG 32 (40 °C)870321563
Hydraulic oil ISO VG 46 (40 °C)875461087
Hydraulic oil ISO VG 68 (40 °C)88068735

The ISO VG grade of an oil is its kinematic viscosity at 40 °C in mm²/s (cSt); the density is the typical one for a mineral oil. Automotive diesel (EN 590 standard) has between 2 and 4.5 cSt at 40 °C: the list uses a typical value of 3 cSt. If you know the data for your fluid, choose “Other” and type them in.

Ducts that are not round

Use the hydraulic diameter instead of the diameter:

Dh = 4 · A / P

Where A is the cross-sectional area of the duct and P its wetted perimeter. In a square duct of side a, Dh = a; in a rectangular one with sides a and b, Dh = 2 · a · b / (a + b).

Advertisement

Frequently asked questions

What are the limits between laminar and turbulent flow?

In circular pipes, flow is laminar below Re = 2300, transitional between 2300 and 4000 and turbulent above 4000. These are practical values: in a very smooth pipe with no vibration, laminar flow can last a little longer.

Which viscosity do I use, dynamic or kinematic?

Either one: Re = ρ · v · D / μ = v · D / ν, because kinematic viscosity is dynamic viscosity divided by density (ν = μ / ρ). With the kinematic viscosity you do not need the density. Choose “Other” with the one you have.

Which diameter do I use if the duct is not round?

The hydraulic diameter: Dh = 4 · A / P, four times the cross-sectional area divided by the wetted perimeter. In a square duct of side a, Dh = a.

Why does it change so much with temperature?

Because the viscosity of water drops a lot as it heats up: at 80 °C it is almost a third of its value at 0 °C. At the same velocity, hot water has a much higher Reynolds number.

Does it work for gases?

Yes, with the density and viscosity of the gas at the conditions in the pipe. The air in the list is at 20 °C and atmospheric pressure; if it is compressed, its density is higher and you should use “Other”.

Related calculators

Share

WhatsApp X LinkedIn Telegram Email
Advertisement

Install Diseño y automatización de instalaciones industriales on your phone

All the calculators one tap away, full screen, like an app. It takes no space and is always up to date.