Skip to content
EN
  • Español
  • English
Advertisement

Earth resistance calculator: ground rods, ring and grid

Calculate the resistance of an earthing system with ground rods, buried conductor, ring, plate or grid (ITC-BT-18), the rods you need and the RCD check.

Fill in 3 of the 4 fields and the missing one is calculated. You can type in any of them.

Values from ITC-BT-18. If you have measured it, choose “Other” and enter the resistivity.
Rod: buried length. Conductor and ring: total length. Grid: total length of its conductors.
Rods spaced at least twice their length apart. For rings and grids, 1.
Enter the one you want to achieve to find out how many rods or what length you need.
Maximum resistance with that RCD (UL / IΔn)—
Complies: margin up to the maximum—
Does not comply: excess over the maximum—
Touch voltage when the RCD trips (R · IΔn)—
Resistance of a single electrode—
Electrodes needed (rounded up)—
Resistance with that number of electrodes—
Minimum spacing between rods (2 L)—

Use this calculator for reference only, as we cannot guarantee that the results are free of errors.

Disclaimer

https://dyaii.es/en/earth-resistance-calculator/

Advertisement

The earthing system carries the current of a fault into the ground so that no exposed metal part is left at a dangerous voltage. The lower its resistance, the lower that voltage. With this calculator you get the resistance of an earthing system with ground rods, buried conductor, ring, plate or grid according to ITC-BT-18 of Spain's Low-Voltage Regulation (REBT), and also the other way round: how many rods or what length you need for a given resistance. It also checks whether it complies with the RCD (residual-current device) you have.

How to use the calculator

  1. Choose the electrode: vertical ground rod, conductor buried horizontally, ring around the building, plate or grid.
  2. Choose the soil (its resistivity is filled in) or enter the resistivity you have measured.
  3. Enter the length (the perimeter for the plate) and how many identical electrodes you install in parallel. You get the resistance.
  4. The other way round: enter the resistance you want and the number of rods is calculated (or the length, if that is what you leave empty). With a measured resistance, the soil resistivity is calculated.
  5. Choose the limit voltage and the RCD sensitivity to check whether the earthing system complies.

ITC-BT-18 formulas

Table 5 of ITC-BT-18 gives these formulas to estimate the earth resistance from the soil resistivity ρ (Ω·m):

ElectrodeEarth resistance (Ω)Data
Vertical ground rodR = ρ / LL: length of the rod (m)
Conductor buried horizontallyR = 2 · ρ / LL: length of the conductor (m)
Buried plateR = 0.8 · ρ / PP: perimeter of the plate (m)

The ring is a horizontally buried conductor that surrounds the building, so it is calculated with R = 2 · ρ / L, with L the length of the ring. For the grid, which is not in the table, the calculator uses Laurent's formula:

R = ρ / (4 · r) + ρ / L

Where r = √(A/π) is the radius of the circle with the same area as the grid and L the total length of its conductors.

Advertisement

Several rods in parallel

With n identical electrodes in parallel, the resistance is approximately:

R total ≈ R of one electrode / n
Only if they are well spaced: rods, at least twice their length apart. Closer together, their areas of influence overlap and the real resistance is higher than R/n. If the calculator asks for 3.1 rods, install 4: it tells you the resistance you will get.

Soil resistivity

Average values from table 4 of ITC-BT-18, for approximate calculations:

SoilResistivity (Ω·m)
Arable and fertile land, compact and moist fill50
Poorly fertile arable fill and other fill500
Bare stony ground, dry permeable sand3000

Indicative values from table 3:

SoilResistivity (Ω·m)
Marshlandfrom a few units to 30
Silt20 to 100
Humus10 to 150
Wet peat5 to 100
Plastic clay50
Marl and compact clay100 to 200
Jurassic marl30 to 40
Clayey sand50 to 500
Siliceous sand200 to 3000
Stony ground covered with grass300 to 500
Bare stony ground1500 to 3000
Soft limestone100 to 300
Compact limestone1000 to 5000
Fissured limestone500 to 1000
Slate50 to 300
Mica and quartz rock800
Weathered granite and sandstone1500 to 10,000
Highly weathered granite and sandstone100 to 600

When the table gives a range, the calculator takes the highest value, the worst case. The real resistivity depends on moisture and temperature: for a major installation, measure it with an earth tester (Wenner method).

Checking with the RCD

ITC-BT-18 requires that no exposed conductive part can produce touch voltages above 24 V in conductive (damp) locations or 50 V elsewhere. With an RCD of sensitivity IΔn, the highest fault current that flows without tripping it is IΔn, so:

R ≤ UL / IΔn
RCDMaximum R with 50 V (Ω)Maximum R with 24 V (Ω)
30 mA1667800
100 mA500240
300 mA16780
500 mA10048
1 A5024

The touch voltage when the RCD trips is Uc = R · IΔn.

Worked example

A 2 m ground rod in arable land (ρ = 50 Ω·m):

R = 50 / 2 = 25 Ω

With a 30 mA RCD and 50 V, the maximum is 50 / 0.03 ≈ 1667 Ω: it complies easily, and the touch voltage would be 25 · 0.03 = 0.75 V.

In poorly fertile fill (ρ = 500 Ω·m), a 2 m rod gives 250 Ω. If you want to get down to 80 Ω to have a margin with a 300 mA RCD (maximum 167 Ω):

n = 250 / 80 = 3.125 → 4 rods → R ≈ 250 / 4 = 62.5 Ω

Spaced at least 2 · 2 = 4 m apart.

Advertisement

Frequently asked questions

What earth resistance does Spain's REBT require?

One that ensures no exposed conductive part can reach more than 24 V in damp locations or 50 V elsewhere (ITC-BT-18). With an RCD, that means R ≤ UL / IΔn: with a 30 mA one and 50 V, up to 1667 Ω; with a 300 mA one, up to 167 Ω.

How many ground rods do I need?

Enter the resistance you want and the calculator gives you the number of rods. Each rod of length L gives R = ρ / L; with n well-spaced rods, the resistance is approximately R / n.

How far apart should the rods be?

At least twice their length: with 2 m rods, 4 m or more. If they are closer, their areas of influence overlap and the resistance of the set is higher than R / n.

What resistivity do I enter if I have not measured it?

Choose the soil from the list: they are the values in tables 3 and 4 of ITC-BT-18. When the table gives a range, the calculator takes the highest value, the worst case. For a major installation, measure it (Wenner method) and enter the measured value.

Does the earth resistance change over time?

Yes: it rises in dry or frozen soil. That is why rods are driven more than 0.5 m deep and ITC-BT-18 requires the earthing system to be checked in the driest season of the year.

Related calculators

Share

WhatsApp X LinkedIn Telegram Email
Advertisement

Install Diseño y automatización de instalaciones industriales on your phone

All the calculators one tap away, full screen, like an app. It takes no space and is always up to date.