Skip to content
EN
  • Español
  • English
Advertisement

Reactance, impedance and resonant frequency calculator for RLC circuits

Calculate inductive and capacitive reactance, impedance, phase angle, current and resonant frequency of a series or parallel RLC circuit.

Fill in 3 of the 6 fields and the rest are calculated. You can type in any of them.

Used to calculate the current and the voltage or current of each element.
Impedance (|Z|)—
Impedance angle φ (+ inductive, − capacitive)—
Net reactance (XL − XC)—
Power factor (cos φ)—
Total current—
Voltage across the resistor—
Voltage across the inductor—
Voltage across the capacitor—
Current through the resistor—
Current through the inductor—
Current through the capacitor—
Quality factor (Q)—
Bandwidth (f₀ / Q)—

Use this calculator for reference only, as we cannot guarantee that the results are free of errors.

Disclaimer

https://dyaii.es/en/rlc-impedance-calculator/

Advertisement

In alternating current, inductors and capacitors oppose the flow of current without heating up: that is reactance. Together with resistance they make up the impedance of the circuit, which sets how much current flows and with what phase shift. This calculator gives you the inductive and capacitive reactance, the impedance, the angle φ, the current and the resonant frequency of a series or parallel RLC circuit. It also works backwards: the inductor or capacitor for a given resonant frequency, or the frequency at which you get a given reactance.

How to use the calculator

  1. Choose the circuit: series or parallel RLC. Enter the resistance and the applied voltage (RMS value), which is used for the current.
  2. Of these six values, enter three: inductance, capacitance, frequency, inductive reactance, capacitive reactance or resonant frequency. The other three are calculated.
  3. For example, enter the resonant frequency you want: with the capacitance and the frequency already filled in, the calculator gives you the inductor.
Some sets of three are not enough because one value follows from the other two: the capacitive reactance from the frequency and the capacitance, the inductive reactance from the frequency and the inductance, or the resonance from the inductance and the capacitance. If that happens, clear the field you want to calculate.

Reactance formulas

XL = 2π · f · L · XC = 1 / (2π · f · C)

Where XL is the inductive reactance (Ω), XC the capacitive reactance (Ω), f the frequency (Hz), L the inductance (H) and C the capacitance (F). The reactance of the inductor grows with frequency and that of the capacitor drops.

Advertisement

Impedance and phase angle

CircuitImpedanceAngle φ
Series RLCZ = √(R² + (XL − XC)²)tan φ = (XL − XC) / R
Parallel RLC1 / Z = √(1 / R² + (1 / XC − 1 / XL)²)tan φ = R · (1 / XL − 1 / XC)

With a positive φ the circuit is inductive (the current lags the voltage) and with a negative φ, capacitive (the current leads). The current is I = U / Z and the power factor, cos φ. In series, each element has its own voltage (UR = I · R, UL = I · XL, UC = I · XC); in parallel, each branch its own current (IR = U / R, IL = U / XL, IC = U / XC).

Resonant frequency

f₀ = 1 / (2π · √(L · C))

At that frequency XL = XC and the two reactances cancel out: the impedance is just R. In series it is the minimum impedance (maximum current); in parallel, the maximum (the source supplies the least current). Solving for them, the inductor or capacitor for a given resonance are:

L = 1 / ((2π · f₀)² · C) · C = 1 / ((2π · f₀)² · L)

The quality factor tells you how sharp the resonance is: Q = √(L / C) / R in series and Q = R · √(C / L) in parallel. The bandwidth (between the −3 dB points) is f₀ / Q.

In a series circuit at resonance, the voltage across the inductor and across the capacitor is Q times the source voltage: with Q = 10 and 230 V, each one withstands 2300 V. Keep it in mind when choosing the capacitor.

Worked example

A series RLC circuit with R = 100 Ω, L = 100 mH and C = 10 µF, connected to 230 V and 50 Hz:

XL = 2π · 50 · 0.1 ≈ 31.42 Ω · XC = 1 / (2π · 50 · 0.00001) ≈ 318.31 Ω
Z = √(100² + (31.42 − 318.31)²) ≈ 303.82 Ω · φ = arctan(−286.89 / 100) ≈ −70.78°

The circuit is capacitive and a current of I = 230 / 303.82 ≈ 0.757 A flows (cos φ ≈ 0.329). The resonant frequency is f₀ = 1 / (2π · √(0.1 · 0.00001)) ≈ 159.15 Hz. For it to resonate at 50 Hz with that capacitor, the inductor would have to be 1 / ((2π · 50)² · 0.00001) ≈ 1.013 H.

Reactance vs. frequency

Component50 Hz1 kHz100 kHz
10 mH inductor3.14 Ω62.83 Ω6.28 kΩ
100 µH inductor0.031 Ω0.628 Ω62.83 Ω
100 µF capacitor31.83 Ω1.59 Ω0.016 Ω
100 nF capacitor31.83 kΩ1.59 kΩ15.92 Ω
Advertisement

Frequently asked questions

What is the difference between resistance, reactance and impedance?

Resistance (R) dissipates energy as heat. Reactance (X) is the opposition of inductors and capacitors to alternating current: it stores energy and gives it back, without heating up. Impedance (Z) is the combination of both, taking the phase shift into account: in series, Z = √(R² + (XL − XC)²). All three are measured in ohms.

What happens at the resonant frequency?

The reactances of the inductor and the capacitor are equal and cancel out. In series, the impedance is at its minimum (only R remains) and the current at its maximum; in parallel, the impedance is at its maximum and the current drawn from the source is at its minimum. The voltage across the inductor or the capacitor of a series circuit can be much higher than the source voltage.

How do I calculate the inductor or the capacitor for a given resonant frequency?

Enter the resonant frequency you want and the component you already have: the calculator solves for the other one with f₀ = 1 / (2π · √(L · C)). For example, with 10 µF and f₀ = 50 Hz you need a 1.013 H inductor.

Why does capacitive reactance drop as the frequency rises?

Because the capacitor charges and discharges more times per second and lets more current through: XC = 1 / (2π · f · C). The inductor does the opposite: XL = 2π · f · L grows with frequency. That is why a capacitor passes high frequencies and an inductor passes low ones.

What is the quality factor Q?

It measures how sharp the resonance is. In series, Q = √(L / C) / R; in parallel, Q = R · √(C / L). With a high Q, the circuit only responds near f₀: the bandwidth is f₀ / Q.

Related calculators

Share

WhatsApp X LinkedIn Telegram Email
Advertisement

Install Diseño y automatización de instalaciones industriales on your phone

All the calculators one tap away, full screen, like an app. It takes no space and is always up to date.