Skip to content
EN
  • Español
  • English
Advertisement

Cable tray bend and offset calculator

Cable tray bend calculator: cut table, formulas and marking dimensions for horizontal and vertical bends and offsets, step by step and in PDF.Version 3 · First version: July 2019 · Remastered: October 12, 2026

Enter the data: the results are calculated instantly.

Horizontal: you cut the base and the inner side rail. Vertical: you cut both side rails (for a downward bend, the base too).
From 1 to 10. With more cuts the bend is smoother and each cut is smaller.
Cut factor (the “0.4”)—
Size of each cut, on each side of the centerline (E)—
Turn of each cut—
Start → 1st apex, opposite side (F)—
Between apexes, opposite side (G)—
Last apex → end, opposite side (H)—
Sloped section: 1st bend centerline → base cut (S)—
Horizontal advance of the sloped section (X)—
Start → centerline of 2nd bend—
Total tray length (I)—
Advance of segment 1—
Advance of segment 2—
Advance of segment 3—
Advance of segment 4—
Advance of segment 5—
Advance of segment 6—
Advance of segment 7—
Advance of segment 8—
Advance of segment 9—
Total advance of the segments (N)—
Advance from the start, F + N (O)—
Advance from the end, H + N (P)—

Use this calculator for reference only, as we cannot guarantee that the results are free of errors.

Disclaimer

https://dyaii.es/en/cable-tray-bend-calculator/

Advertisement

To bend a cable tray you cut V-shaped wedges and bend the tray until the cuts close. This calculator gives you the size of each cut and all the dimensions to mark the tray, for horizontal and vertical bends as well as offsets (changes of level). The drawing takes you step by step, with your dimensions: tap the numbers or “Play”.

How to use the calculator

  1. Choose what you want to make: a bend or an offset (change of level).
  2. For a bend, say whether it is horizontal or vertical (upward or downward), the angle and the number of cuts, from 1 to 10: with more cuts the bend is smoother.
  3. Type the tray width (A) and the side rail height (h), and the distances on the cut side: from the start to the first cut (B), between cuts (C) and from the last cut to the end (D).
  4. You get the size of each cut (E), the dimensions on the opposite side (F, G, H), the tray length (I) and the advances to check the bend. You can use any unit and choose the decimals with the “Decimals” button.

How to mark and cut a horizontal bend

  1. Measure and cut a piece of tray of length I.
  2. Mark the apexes on the side opposite the cut (the outside of the bend): F from the start, G between apexes and H to the end.
  3. Mark the gaps on the cut side (the inside): B, a gap of 2·E, C, another gap of 2·E… and D to the end.
  4. Draw the Vs by joining the ends of each gap to its apex. On the inner side rail, mark a rectangle as wide as the gap.
  5. Cut the wedges in the base and the rectangles in the inner side rail. The outer side rail is not cut: it acts as the hinge.
  6. Bend the tray until the cuts close and join each cut with its splice plate or bolts. Check the advances O and P.

In a vertical upward bend both side rails are cut in a V with the opening at the top edge, and the base acts as the hinge. Downward, the V has its opening at the base and a strip of the base 2·E wide is also removed at each cut: there the hinge is the top edge of the side rails. In both, E is calculated with the side rail height.

Advertisement

Where does the 0.4 come from?

Each V cut is an isosceles triangle: two identical right triangles, one on each side of the centerline. If a cut turns the tray by an angle of α / n, each triangle has half that angle at the apex, and its long leg is the tray width (or the side rail height). By trigonometry, the short leg, which is the size of each side of the cut, is:

E = A · tan(α / 2n)

In the most common bend, 90° in two cuts, each cut turns 45° and each triangle has 22.5°: tan(22.5°) = 0.4142. That is the famous “0.4”: on a 100 mm tray, each side of the cut measures 41.4 mm (about 40 mm if rounded). It is the same factor in an offset with 45° bends made with a single cut.

Rounding to 0.4 has a cost: each cut turns 43.6° instead of 45°, so the 90° bend ends up at about 87° and drifts about 49 mm for every meter of tray. That is why the calculator always uses the exact factor, which is shown in the results.

Factor tan(α / 2n) for a 90° bend by number of cuts:

Cuts123456810
Turn of each cut90°45°30°22.5°18°15°11.25°9°
Factor1.00000.41420.26790.19890.15840.13170.09850.0787

Offsets (changes of level)

An offset raises or lowers the tray from one height to another. You make two identical vertical bends, usually 45°: in the lower one the V has its opening at the top edge of the side rails; in the upper one, at the base, and a strip of the base is also removed. Between the two is the sloped section, which is the hypotenuse of a right triangle whose legs are the rise and the advance:

S = H / sin β  ·  X = H / tan β  ·  E = h · tan(β / 2)

Where H is the rise between the bases of the two runs, β the angle of each bend and h the side rail height. S is measured on the base, from the centerline of the first bend to the start of the strip removed in the second.

Example: to rise 1000 mm with 45° bends on a tray with 100 mm side rails, the sloped section measures S = 1000 / sin 45° = 1414 mm, advances X = 1000 mm and each side of the cut measures E = 100 · 0.4142 = 41 mm.

Measure the rise between the bearing faces of the tray on the two supports, not between the outsides of the supports: a few centimeters of difference change the sloped section.

Bend formulas

Each cut turns the tray α / n. The dimensions on the opposite side and the total tray length:

F = B + E  ·  G = C + 2E  ·  H = D + E
I = B + D + (n − 1) · C + 2 · n · E

The advance of each segment is its projection onto the initial direction:

advance of segment k = G · cos(k · α / n)

N is the sum of the advances of the segments, O = F + N and P = H + N.

Worked example

Horizontal 90° bend in 3 cuts on a 300 mm tray, with B = 200 mm, C = 100 mm and D = 200 mm:

E = 300 · tan(15°) = 300 · 0.2679 ≈ 80 mm

F = 280 mm, G = 261 mm, H = 280 mm and the tray needed is I = 1082 mm long. The advances are 226 mm and 130 mm, so N = 356 mm and O = P = 637 mm.

Size of each cut for a 90° bend

Value of E in millimeters by tray width (or side rail height) and number of cuts.

Width (mm)1 cut2 cuts3 cuts4 cuts5 cuts6 cuts8 cuts10 cuts
606025161210865
1001004127201613108
15015062403024201512
20020083544032262016
300300124806048393024
4004001661078063533931
5005002071349979664939
60060024916111995795947
Advertisement

Frequently asked questions

Can I get the cut table as a PDF?

Yes: with “Print / PDF” you save a sheet with your dimensions, the drawing, the marking table and the full step-by-step guide, like a manual to take to the job site.

How do you make an offset in a cable tray?

An offset is a change of level: two identical vertical bends, usually 45°, with a sloped section between them. Choose “Offset (change of level)”, type the rise and the side rail height, and the calculator gives you the cuts and the length of the sloped section.

What is the “0.4” used when bending cable tray?

It is the tangent of 22.5°, which is 0.4142. In a 90° bend made with two cuts, each cut turns 45° and each half of the V, 22.5°: that is why each side of the cut is 0.4142 times the width (or the side rail height). Rounding to 0.4 makes the bend close at about 87°; the calculator uses the exact value for any angle.

How many cuts should I make?

With more cuts the bend is smoother and each cut is smaller, but there is more work. For a 90° bend, 2 or 3 cuts are usually enough on trays up to 300 mm, and 4 to 6 on wider trays. The calculator allows up to 10.

How do you make a change of level?

With two identical vertical bends (for example, 45°): in the lower one the side rails are cut in a V from the top; in the upper one, in a V from the base, and a strip of the base is removed. The sloped section between them is the rise divided by the sine of the angle (1000 mm at 45° is 1414 mm).

How many decimals do the results have?

2 by default. On site you mark to the millimeter: choose 0 with the “Decimals” button. When adding rounded values, the total length can vary by ±1 mm.

Version history
  • Version 3 · October 12, 2026: Remasterización: proceso paso a paso interactivo, de 1 a 10 cortes, curvas verticales, cambios de nivel, cualquier unidad, PDF y Excel.
  • Version 2: Calculadoras de curvas (sencilla y avanzada): de 2 a 5 cortes con las cotas de marcado.
  • Version 1 · July 2019: Guía «Cómo curvar bandeja portacables»: curva de 90° en dos cortes con el factor 0,4 y cambios de nivel.

Related calculators

Share

WhatsApp X LinkedIn Telegram Email
Advertisement

Install Diseño y automatización de instalaciones industriales on your phone

All the calculators one tap away, full screen, like an app. It takes no space and is always up to date.